PHT www.vishay.com vishay sfernice revision: 14-jan-15 1 document number: 53050 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 high stability - high temperature (230 c) thin film wraparound chip resistors, sulfur resistant introduction for applications such as down hole applications, the need for parts able to withstand very severe conditions (temperature as high as 215 c powered or up to 230 c un-powered) has leaded vishay sfernice to push out the limit of the thin film technology. ? designers might read the application note: power dissipation considerations in high precision vishay sfernice thin film ch ip resistors and arrays (p, pra etc) (high temperature application) www.vishay.com/doc?53047 in conjunction with this datasheet to help them to pro perly design their pcbs and get the best perfo rmances of the PHT. vishay sfernice r&d engineers will be willing to support any customer design considerations. features ? operating tempe rature range: ? -55 c; +215 c ? storage temperature: -55 c; +230 c ? gold terminations (< 1 m thick) ? 5 sizes available (0402, 0603, 0805, 1206, 2010); other sizes upon request ? temperature coefficient down to 15 ppm ? (-55 c; +215 c) ? tolerance down to 0.01 % ? load life stability: 0.35 % max. after 2000 h at 220 c (ambient) at pn ? shelf life stability: 0.7 % typ. (1 % max.) after 15 000 h at 230 c ? smd wraparound ? tcr remains constant after long term storage at 230 c (15 000 h) ? sulfur resistant (per astm b809-95 humid vapor test) ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 notes (1) for power handling improvem ent, please refer to application note 53047: power dissipation consid erations in high precision vis hay sfernice thin film chip resistors and arrays (high temperature applications) www.vishay.com/doc?/53047 and consult vishay sfernice (2) see table 2 on next page (3) see table 1 on next page (4) it is possible to dissipate up to 0.3 w, but there will be an additional drift of 0.1 % after load life note ? for other terminat ions, please consult standard electrical specifications model size resistance range ? rated power (1)(2) p 215 c w limiting element voltage v tolerance (2) % temperature coefficient (3) ppm/c PHT0402 0402 10 to 130k 0.0189 50 0.01, 0.02, 0.05, 0.1, 0.5, 1 10, 15, 25, 30, 50, 55 PHT0603 0603 10 to 320k 0.0375 75 0.01, 0.02, 0.05, 0.1, 0.5, 1 10, 15, 25, 30, 50, 55 PHT0805 0805 10 to 720k 0.06 150 0.01, 0.02, 0.05, 0.1, 0.5, 1 10, 15, 25, 30, 50, 55 PHT1206 1206 10 to 2.7m 0.1 200 0.01, 0.02, 0.05, 0.1, 0.5, 1 10, 15, 25, 30, 50, 55 PHT2010 2010 10 to 7.5m 0.2 (4) 300 0.01, 0.02, 0.05, 0.1, 0.5, 1 10, 15, 25, 30, 50, 55 climatic specifications operating temperature range -55 c; +215 c storage temperature range -55 c; +230 c performance vs. humid sulfur vapor test conditions 50 c 2 c, 85 % 4 % rh, exposure time 500 h test results resistance drift < (0.05 % r + 0.05 ? ), no corrosion products observed mechanical specifications substrate alumina resistive element nichrome (nicr) passivation silicon nitride (si 3 n 4 ) protection epoxy + silicone terminations gold (< 1 m) over nickel barrier
PHT www.vishay.com vishay sfernice revision: 14-jan-15 2 document number: 53050 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 PHT stability curve note ? stability will be dependent on resistivity of resistor. above curves are worst case. table 1 - temperature coefficient y 10 ppm/c -55 c; +155 c 15 ppm/c -55 c; +215 c e 25 ppm/c -55 c; +155 c 30 ppm/c -55 c; +215 c h 50 ppm/c -55 c; +155 c 55 ppm/c -55 c; +215 c table 2 - best tolerance and tcr vs. ohmic value series range ( ? ) tol. ( %) tcr code 0402 10 to < 100 0.05; 0.1; 0.5; 1 y; e; h 100 to < 90k 0.01; 0.02; 0.05; 0.1; 0.5; 1 y; e; h 90k to 130k 0.01; 0.02; 0.05; 0.1; 0.5; 1 e; h 0603 10 to < 100 0.05; 0.1; 0.5; 1 y; e; h 100 to < 210k 0.01; 0.02; 0.05; 0.1; 0.5; 1 y; e; h 210k to 320k 0.01; 0.02; 0.05; 0.1; 0.5; 1 e; h 0805 10 to < 100 0.05; 0.1; 0.5; 1 y; e; h 100 to < 480k 0.01; 0.02; 0.05; 0.1; 0.5; 1 y; e; h 480k to 720k 0.01; 0.02; 0.05; 0.1; 0.5; 1 e; h 1206 10 to < 100 0.05; 0.1; 0.5; 1 y; e; h 100 to < 1.8m 0.01; 0.02; 0.05; 0.1; 0.5; 1 y; e; h 1.8m to 2.7m 0.01; 0.02; 0.05; 0.1; 0.5; 1 e; h 2010 10 to < 100 0.05; 0.1; 0.5; 1 y; e; h 100 to < 5m 0.01; 0.02; 0.05; 0.1; 0.5; 1 y; e; h 5m to 7.5m 0.01; 0.02; 0.05; 0.1; 0.5; 1 e; h 0.0 drift in % time in h high temperature drift vs. time 0 2000 4000 6000 8000 10 000 12 000 14 000 0.2 0.4 0.8 1.2 1.6 1.8 2.0 1.4 0.6 1.0 with pd (t j = 230 c) t = 185 c t = 200 c t = 215 c t = 230 c
PHT www.vishay.com vishay sfernice revision: 14-jan-15 3 document number: 53050 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 power derating curve dimensions in millimeters (inches) suggested land pattern (to ipc-7351a) caution : performances obtained with following mounting conditions: pcb: polyimide solder paste: pbsnag (93.5/5/1.5) case size ab c d/e max. tol. +0.152 (+0.006) min. tol. -0.152 (-0.006) max. tol. +0.127 (+0.005) min. tol. -0.127 (-0.005) nominal nominal nominal tolerance 0402 1.00 (0.039) 0.60 (0.024) termination n: 0.5 (0.02) 0.127 (0.005) termination g: 0.4 (0.016) 0.051 (0.002) 0.25 (0.010) 0.1 (0.004) 0603 1.52 (0.060) 0.85 (0.033) 0.38 (0.015) 0.13 (0.005) 0805 1.91 (0.075) 1.27 (0.050) 1206 3.06 (0.120) 1.60 (0.063) 0.40 (0.016) 2010 5.08 (0.200) 2.54 (0.100) 0.48 (0.019) chip size dimensions (in millimeter) z max. g min. x max. 0402 1.55 0.15 0.73 0603 2.37 0.35 0.98 0805 2.76 0.74 1.40 1206 3.91 1.85 1.73 2010 5.93 3.71 2.67 ambient temperature in c rated power (%) 350 300 250 200 150 100 50 0 50 200 100 250 0150 a d d c e e b g min. z max. x max.
PHT www.vishay.com vishay sfernice revision: 14-jan-15 4 document number: 53050 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 popular options it is recommended to consult vishay sfernice for availability first. option: enlarged terminations: for stringent and special power dissipation requirements, the thermal resistance between the resistive layer and the solder joi nt can be reduced using enlarged te rminations chip resistors which are soldered on large and thick copper pads acting as heatsink (see application note: 53048 power dissipati on in high precision vishay sfernice chip resistors and arrays (p thin film, pra arrays, chp thick film) www.vishay.com/doc?53048 . option to order: 0063 (applies to size 1206 / 2010). dimensions (option 0063) in millimeters suggested land pattern (option 0063) case size abed f max. tol. +0.152 min. tol. -0.152 max. tol. +0.127 min. tol. -0.127 max. tol. +0.13 min. tol. -0.13 max. tol. +0.13 min. tol. -0.13 nominal nominal nominal nominal nominal min. max. 1206 3.06 1.60 0.40 1.215 0.63 0.50 0.76 2010 5.08 2.54 0.48 2.25 chip size dimensions (in millimeter) z max. g min. x max. 1206 3.91 0.50 1.73 2010 5.93 2.67 a b d e f enlarged termination uncoated ceramic bottom view for mounting g min. z max. x max.
PHT www.vishay.com vishay sfernice revision: 14-jan-15 5 document number: 53050 for technical questions, contact: sferthinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 packaging esd packaging available: waffle-pack and plastic tape and reel (low conductivity). paper tape available in standard (for size 0402) and upon request (esd only) (for sizes 0603, 0805, and 1206). note (1) 12 mm on request packaging rules waffle pack ? can be filled up to maximum qu antity indicated in the table here above, taking into account the minimum order quantity. when quantity ordered exce eds maximum quantity of a single waffle pack, the waffle packs are stacked up on the top of each other and closed by one single cover. ? to get not stacked up waffle pack in case of ordered quantity > maximum number of pieces per package: please consult vish ay sfernice for sp ecific ordering code. tape and reel ? can be filled up to maximum qu antity indicated in the table here above, taking into account the minimum order quantity. when quantity ordered is between the moq and the maximum reel capacity, on ly one reel is provided. ? when several reels are needed for ordered quantity within moq and maximum reel capacity: please consult vishay sfernice for specific ordering code. note (1) for usage at temperatures up to 200 c maximum n (tin/silver termin ation are available upon request) size moq number of pieces per package tape width waffle pack 2" 2" tape and reel min. max. 0402 100 100 100 5000 8 mm 0603 0805 4000 1206 140 2010 60 2000 8 mm (1) global part number information global part numbering: PHT1206y1001bgt063 global model size tcr value tolerance termination packaging option PHT 0402 0603 0805 1206 2010 y e h the first three digits are significant figures and the last digit specifies the number of zeros to follow, r designates decimal point 10r0 = 10 ? 3901 = 3900 ? 1004 = 1 m ? l = 0.01 % p = 0.02 % w = 0.05 % b = 0.1 % d = 0.5 % f = 1 % g = gold n = tin/silver (1) for more information see codification of packaging table leave blank if no option codification of packaging code 18 packaging waffle pack w 100 min., 1 mult wa 100 min., 100 mult (ava ilable only on size 1206) plastic tape (in standard for all sizes except 0402) t 100 min., 1 mult ta 100 min., 100 mult tb 250 min., 250 mult tc 500 min., 500 mult td 1000 min., 1000 mult te 2500min., 2500 mult tf full tape (quantity depending on size of chips) paper tape (in standard for 0402, option for other sizes) pt 100 min., 1 mult pa 100 min., 100 mult pb 250 min., 250 mult pc 500 min., 500 mult pd 1000 min., 1000 mult pe 2500min., 2500 mult pf full tape (quantity depe nding on size of chips) ht1206y10 p 01bgt 06 3
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
